temperature programming
英 [ˈtemprətʃə(r) ˈprəʊɡræmɪŋ]
美 [ˈtemprətʃər ˈproʊɡræmɪŋ]
网络 程序升温; 温度程序
双语例句
- A temperature programming gas chromatography ( GC) was developed for the determination of volatile fatty acids in rumen liquor.
建立了程序升温气相色谱法测定羊瘤胃液中的挥发性脂肪酸。 - The influences of temperature programming and the way to add lipase on the contents of monoglycerides ( MG) in reaction mixtures were investigated.
考察了反应温度程序以及加酶方式对最终产物中单甘酯质量分数的影响。 - These coefficients and the experimental relationships are important to the understanding on the TC of the geotechnical materials in north China and to the temperature simulation programming as well.
该系数和这些经验公式的导出对中国北方地区岩土材料导热性能的理解及温度场模拟工作均具重要意义。 - Using SPB 1 capillary column with temperature programming, methyl-and ethyl-mercuries hydrides can be base-line separated within 4 min.
使用SPB－1毛细管柱在4min内可基线分离氢化甲基汞和氢化乙基汞。 - Effect of Error in Temperature Programming Desorption Temperature Measurement on Desorption Kinetic Parameters Calculation
程序升温脱附测温误差对脱附动力学参数的影响规律 - Molybdenum carbide was prepared with n-hexane as carbon source by temperature programming method.
采用程序升温法，以正己烷为碳化原料制备碳化钼，对噻吩加氢脱硫活性进行了评价。 - The Optimum Temperature Raising Control for PVC Polymerization with Dynamic Programming Method
用动态规划方法来实现PVC聚合釜的优化升温控制 - Optimized Linear Temperature Programming for Capillary Gas Chromatography by the Method of Gridding Search
网格搜索法优化毛细管气相色谱线性程序升温 - Laser Raman spectroscopy and temperature programming reduction study of supported tungsten oxide
负载氧化钨催化剂的拉曼光谱和程序升温还原研究 - A Software for Simulation of the Process in Gas Chromatography Column and Optimization of Multi-Step Temperature Programming
气相色谱柱内过程模拟和条件优化软件 - Design of Temperature Collecting System by Microcomputer Based on VB Programming
基于VB编程的微机温度采集系统设计 - The Research of Temperature Programming Group Controller with Double-microcomputer
Ⅰ组只饲喂基础日粮；双微机温度程序群控仪的研制 - The temperature model of the waved-edge has been constructed according to Jaeger's theory of moving solid under the used temperature model of the flat insert, it is possible to forecast milling temperature through programming.
在已有的平前刀面铣刀片铣削温度数学模型的基础上，利用Jaeger的移动面热源理论，建立了波形刃铣刀片铣削温度的数学模型，编制了计算机程序对铣削温度进行了预测； - In this paper, It is discussed the method in the building the mathematical model of characteristic between thermocouple output and temperature ( E-t) using MATLAB language and programming block diagrams of building model as well as applicable examples are introduced in this paper.
文中论述了运用MATLAB语言，建立热电偶热电势和温度（E～t）特性的数学模型的方法，并给出了建模的程序框图及实例。 - With this system, natural gas and regenerator flue gas from catalytic cracking unit can be analyzed within 12 minutes with temperature programming above room temperature.
在室温以上程序升温，直接分析天然气及催化裂化再生气，12分钟内可完成全分析。 - The purification of the menthol from peppermint essential oil has been investigated with supercritical carbon dioxide fractionation at different temperature gradient and step-by-step pressure increasing programming.
进行了利用超临界CO2精密分离技术从薄荷原油中提纯薄荷脑的研究，分别考察了分馏塔温度梯度、升压速率等操作参数对分离效果的影响。 - Calculation of Isothermal Retention Indices from Temperature Programming Data
由气相色谱程序升温数据计算恒温保留指数 - A method for the determination of dimethyl carbonate ( DMC) by GC was set up using OV-1 capillary column, hydrogen flame ionization detector ( FID) and two step temperature programming.
选用OV-1毛细管色谱柱及氢火焰离子化检测器（FID），采用二阶程序升温，建立了测定碳酸二甲酯（DMC）含量的气相色谱法。 - Chapter three will introduce gas flow compensation of temperature and pressure, and its programming of software.
第三章讨论天然气流量全参数温压补偿技术，及其软件编程。 - The cure kinetics of DGEBA/ Dicyandiamide ( DICY) system was investigated under temperature programming curing condition. Differential Scanning Calorimetry ( DSC) was the thermo-analytical technique used to determine the cure kinetics of this system.
采用程序升温差示扫描量热仪（DSC）法研究了DGEBA／双氰胺（DICY）体系的非等温固化反应动力学。 - Meanwhile, a new method of calculating calcination rate coefficient from the data obtained in inert atmosphere and temperature programming was proposed.
本文还提出了从惰性气氛下程序升温数据计算硫酸钙煅烧反应速率常数的方法。 - For actual data of sag, temperature and current, the adoption of MATLAB programming, the use of non-linear regression method of fitting to check the mathematical model, and draw the various coefficients of model.
对实际的弧垂、温度、电流数据，通过MATLAB编程，采用非线性回归拟合的方法对数学模型进行了校验，并得出模型的各个系数。 - The ROM address of the for temperature sensors is searched and distinguished by software programming in order to correspond to the temperature sensor and temperature data.
在软件编程上需要对4个温度传感器的ROM地址进行搜索和识别，以便将温度传感器和温度数据一一对应。 - The software design includes architecture design, system software design, digital filtering process design and the temperature of electrical conductivity which was realized by programming.
软件设计主要包括：软件总体架构的设计、系统的软件设计、数字滤波程序的设计和采用软件编程实现的电导率温度补偿。 - The method of calculating the adiabatic saturated temperature by programming is given and the research shows that the adiabatic saturated temperature is the lowest temperature that makes the air saturated by spraying cooling system.
分析了喷雾冷却的理论过程，指出绝热饱和温度是喷水使空气达到饱和湿空气状态的最低温度，并给出了编程计算绝热饱和温度的方法。